Hits: 1370 img
IOTA OPSZ 1800 is a low-viscosity, solvent-free organosilazane thermosetting coating resin with 99.99% solids. The product data state: coating service temperature up to 1000+°C and peak service temperature up to 1800°C; rapid curing by heating to 200°C; addition of a radical initiator such as dicumyl peroxide can lower the curing temperature, enabling curing within 1 to 90 minutes at 100°C to 180°C, with peroxide initiators typically dissolved in the solvent-free polymer at 0.5 to 1.0% by weight of the polymer; initiator-free systems can be heat-cured at 200–250°C. For high-temperature formulations, the coated substrate needs to be heated to at least 425°C to promote conversion of the polymer to ceramic; heating above 700°C can also promote conversion to ceramic.
Selection should not rely only on “1000+°C,” “1800°C,” or “>9H.” First confirm the substrate and pretreatment, target film thickness, curing route (whether a radical initiator is used), whether high-temperature ceramic conversion is required and the conversion schedule, the typical dosage of 10–60% and solvent compatibility, the final application—high-temperature ceramic coating, heat-stable anti-corrosion coating, or non-stick coating—and the project acceptance criteria for heat resistance, thermal shock, chemical resistance, adhesion, and anti-corrosion. This article does not equate heat resistance, pencil hardness, or chemical resistance with a specific salt-spray duration, scratch-resistance grade, or outdoor service life. IOTA can provide polysilazane raw materials and corresponding product data; the company does not provide complete formulations or formulation development services.
Even with the same organosilazane, one project may focus on no powdering or delamination at high temperature, another on heat-stable anti-corrosion, another on non-stick performance and surface energy, and another on adhesion retention after thermal shock. Different targets require different dosage, film thickness, and curing routes. Typical application directions for OPSZ 1800 include high-temperature ceramic coatings, heat-stable anti-corrosion coatings, and non-stick coatings. Selection should start with the specific problem to be solved, not just “high temperature resistant.”
| What to confirm | What to specify in an inquiry or sample request |
|---|---|
| Service temperature | Continuous working temperature, peak temperature, heating rate, holding time |
| Substrate and pretreatment | Steel or other substrate grade, surface condition, degreasing, derusting, and other treatments |
| Coating build | Single layer or composite system; each layer, target dry film thickness, and curing conditions |
| Curing route | Whether a radical initiator is used; for initiator-free systems, whether 200–250°C heat curing is applied |
| Ceramic conversion | Whether a high-temperature formulation is required; whether the coated substrate needs to be heated to at least 425°C to promote conversion to ceramic; whether treatment above 700°C is also required |
| Formulation conditions | Typical OPSZ 1800 dosage of 10–60%; solvent type and compatibility with alkanes, aromatics, ethers, ketones, and esters |
| Acceptance criteria | Target temperature, thermal shock, adhesion, chemical resistance, salt spray, or cyclic corrosion requirements |
| Sample preparation | Sample size, number of coating passes, film thickness, curing and ceramic conversion records, whether scribed or cut edges are used, sample quantity |
If the customer already has a test specification, obtain the original document first. When criteria are missing, confirm them with the project owner and test laboratory before making samples, so that both sides do not discover different interpretations of “pass” after testing.
OPSZ 1800 can be rapidly cured by heating to 200°C. Adding a radical initiator such as dicumyl peroxide can lower the curing temperature: with a radical initiator, curing can be completed within 1 to 90 minutes at 100°C to 180°C; peroxide initiators are typically dissolved in the solvent-free polymer at 0.5 to 1.0% by weight of the polymer. Initiator-free systems can be heat-cured at 200–250°C.
Therefore, first confirm whether the available equipment can meet the curing temperature and time, and then decide whether to use an initiator route. Initiator dosage, dissolution method, and mixing uniformity should be included in the formulation and process records. A tack-free or low-temperature pre-cured film does not necessarily mean the final curing condition has been reached. Testing a film immediately after surface drying may not represent a coating fully cured under the specified conditions.
The product data note that for high-temperature formulations, the coated substrate may need to be heated to at least 425°C to promote conversion of the polymer to ceramic. The formulation and application section also states that heating above 700°C can promote conversion to ceramic. The actual ceramic conversion schedule should be confirmed with the specific formulation, substrate, heating rate, target temperature, and holding time; it should not be generalized from a single temperature point.
The coating service temperature can reach 1000+°C, and the peak service temperature can reach 1800°C. “Peak service temperature” should be understood as a short-term or peak capability under specific conditions. It should not be converted into a long-term continuous service temperature or an outdoor service life without supporting evaluation. For anti-corrosion coating use, heat resistance is not the same as having passed a specific salt-spray or cyclic corrosion duration. For non-stick coating use, heat resistance is also not the same as scratch resistance or durable non-stick performance.
Typical coating properties of OPSZ 1800 include various colors, matte to silky gloss, typical dosage of 10–60%, thickness of 10–300 μm, pencil hardness >9H, good chemical resistance, heat resistance up to 1800°C, and good thermal shock resistance. The low-viscosity solvent-free system and 99.99% solids are useful for formulation design, but final performance still depends on substrate, pretreatment, film thickness, curing route, whether ceramic conversion has occurred, and whether fillers or other additives are present.
When comparing candidate solutions, keep substrate, pretreatment, and sample preparation as consistent as possible. If film thickness, initiator dosage, or additional layers are changed, record them separately. Results are only for project evaluation under the corresponding conditions; do not use a single property number to create a general ranking of different materials. Pencil hardness >9H is a specific test result and is not the same as a scratch-resistance grade or wear life.
Obtain the customer’s service conditions and acceptance criteria; confirm whether temperature, time, thermal shock, anti-corrosion, and non-stick requirements are targets or existing results.
Specify substrate, surface treatment, each coating layer, target dry film thickness, curing equipment, initiator route, and ceramic conversion schedule.
Check the current IOTA OPSZ 1800 data, then have the user make representative samples and keep records of dosage, solvent, initiator amount, curing, and heating profile.
Arrange tests as agreed; keep sample identity, test conditions, observation photos, and evaluation results in the report. Before expanding use, confirm whether the samples represent actual workpieces.
IOTA/Anhui Iota Silicone Oil Co., Ltd. positions itself as a solution provider across the organosilicon industry chain and can provide polysilazane raw materials and corresponding product data. When communicating, provide the substrate, existing coating practice, target defects, curing equipment, and ceramic conversion conditions together to facilitate candidate screening; the company does not provide complete formulations or formulation development services.
First define the substrate, coating system, curing route, ceramic conversion conditions, and acceptance criteria, and then obtain the corresponding test evidence. 1000+°C is a service-temperature description and should be understood with the specific conditions.
An initiator can lower the curing temperature and enable curing within 1–90 minutes at 100–180°C, but the typical dosage is 0.5–1.0% by weight of the polymer and must be confirmed against the system, dissolution method, and application conditions.
Initiator-free systems can be heat-cured at 200–250°C. Whether the coating is fully cured and whether further ceramic conversion is needed should be confirmed according to the specific formulation and heating schedule.
The data separately mention that high-temperature formulations need to be heated to at least 425°C to promote conversion of the polymer to ceramic, and that heating above 700°C can promote conversion to ceramic. The actual schedule should be confirmed with the formulation, substrate, and target ceramic phase; a single temperature point should not be applied universally.
Peak service temperature is not the same as long-term continuous service temperature and cannot be directly converted into outdoor service life. Long-term use requires the actual temperature profile and evaluation evidence.
Not necessarily. Pencil hardness is a specific test result. Scratch resistance is also affected by film thickness, friction mode, contaminants, and cure degree, and should be evaluated separately by the corresponding method.